Mustek PP3000 Spezifikationen Seite 75
- Seite / 82
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
PST-6000 series Technical Manual 7 - 5
TM
DETACHING THE REAR CABINET
Before detaching the rear cabinet of the PST system, all the external devices
should be removed. Disconnect all the connectors in the rear room within back cover.
Refer to the installation instructions in User’s Manual (take opposite operation in
reverse order) for detaching CRT or LCD display, printer, VFD and if installed, the
built-in battery.
Look into both sides of the PST chassis, with reference to the following
drawing, the user should find a “L” shaped steel wire at each side binding the rear
cabinet to the bottom chassis. Of course, only the short arm of the wire is visible from
the side that was covered by the side wall of the keyboard unit just removed. Turn the
short arms outward by 90 degrees (they were pointing upward) and pull the wires
toward the front till the long arms come out (see DWG.-5). Unscrew the two screws
and take out the washers on the printer platform to get ready to take the rear cabinet
off.
Now, the user would like it better to do the next operation with the PST system
up side down, though it is still possible for some skillful person to do it without
turning the PST. The drawing shows the bottom side of the PST system. The purpose
is to detach all the hooks from their notches. There are three notches on each side wall
of the bottom chassis and there are correspondingly three hooks at the inside of each
side wall of the rear cabinet. The key issue is to detach the hooks by pulling the side
walls of the rear cabinet a little bit outward yet still within the limit of the elasticity of
the cabinet (see DWG.-6). It is normal to have the rearmost pair of hooks more
difficult to get out than the others in this operation. Then the cabinet can be put aside
and the PST turned back to normal position.
Refer to the drawing for cable connections within the PST system and
disconnect those necessary for taking out the module that needs to be replaced (see
DWG.-7).
- PST-6000 SERIES 1
- SOME IMPORTANT NOTES 2
- TABLE OF CONTENTS 3
- OVERVIEW 9
- MODEL NUMBERS 10
- GENERAL SPECIFICATION 11
- OPERATOR DISPLAY 12
- LED COLOR 13
- SYSTEM POWER ON/OFF CONTROL 13
- UPS SUPPORT (battery option) 13
- EXTERIOR 14
- INPUT / OUTPUT PORTS 14
- PRELOAD DOS 14
- PROGRAMMABLE KEYBOARD 15
- ENVIRONMENTAL 15
- ACCESSORIES 16
- CUSTOMER DISPLAY 17
- KEY TOP OPTION 17
- UPS BATTERY 17
- INTERNAL MODEM CARD 17
- IRDA TRANSCEIVER 17
- PS/2 MOUSE CONNECTOR CABLE 18
- PCMCIA CONTROL CARD 18
- CACHE MEMORY EXPANSION 18
- DRAM EXPANSION 18
- PRINTER: PP-3000 18
- MAGNETIC STRIPE READER 19
- RELIABILITY SPECIFICATION 21
- SYSTEM DEFINITIONS 23
- EXTERNAL KEYBOARD CONNECTOR 24
- LAN PORT 24
- PS/2 MOUSE 24
- CRT DISPLAY PORT CONNECTOR 25
- LCD DISPLAY PORT CONNECTOR 25
- SERIAL PORT COM1 25
- SERIAL PORT COM2 26
- SERIAL PORT COM3 27
- SERIAL PORT COM4 27
- PARALLEL PORT LPT1 28
- CUSTOMER DISPLAY CONNECTOR 29
- CASH DRAWER CONTROLLER 29
- 24 VDC CONNECTOR 30
- UPS BATTERY CONNECTOR 30
- APPLICATION GUIDES 31
- PD-2101 (VFD DISPLAY) 34
- Futaba emulation mode 35
- Noritake emulation mode 36
- PD-7001 (LCD DISPLAY) 39
- -- 2 LINES X 20 CHARACTERS 40
- (CONTINUED 1) 43
- (CONTINUED 2) 44
- -- 4 LINES X 26 CHARACTERS 45
- COMMON PROGRAMMING (KBM.EXE) 49
- IN ASCII-CODE EDITING MODE 50
- IN SCAN-CODE EDITING MODE 51
- ANSWER BACK CODE 52
- SHORTCUT UTILITY (RWM.EXE) 52
- HARDWARE LIMITATION 53
- POWER ON/OFF CONTROL 54
- HARDWARE DETAILS 59
- RAM/VGA SELECT AREA DETAIL 60
- JUMPERS AND CONNECTORS 60
- JUMPER SETTINGS 62
- CPU/PCI CLOCK SELECT 63
- CLOCK RATIO SELECT 64
- EXAMPLE CPU JUMPER SETTINGS 64
- DRAM BANK SELECT 65
- DIMM SOCKET VOLTAGE SELECT 65
- CACHE SIZE SELECT 66
- INTERNAL VGA SELECT 66
- INTERNAL VGA ID SELECT 66
- CMOS MEMORY SELECT 66
- COM1 DC SUPPLY SELECT 67
- COM2 DC SUPPLY SELECT 67
- COM3 DC SUPPLY SELECT 67
- COM4 DC SUPPLY SELECT 67
- COM3 ENABLE 67
- MODIFICATION FOR MSR 69
- LCD CARD (PST033) 70
- SERVICE AND SPARE PARTS 71
- DWG. - 2 Unscrew the bottom 73
- DETACHING THE REAR CABINET 75
- SPARE PARTS/MODULE LIST 78
- ASSEMBLY DRAWING 82
Verwandte Produkte und Handbücher für Drucken & Scannen Mustek PP3000
Drucken & Scannen Mustek PP3000 Bedienerhandbuch
(78 Seiten)
(78 Seiten)
Drucken & Scannen Mustek PP3000 Spezifikationen
(79 Seiten)
(79 Seiten)
Electrolux EWW1476WD manuals
Owner’s manuals and user’s guides for Tumble dryers Electrolux EWW1476WD.
We providing 2 pdf manuals Electrolux EWW1476WD for download free by document types: User Manual
Kommentare zu diesen Handbüchern